pro tm programmable clock oscillator technical data pro tm s8002 ceramic series saronix 3.3 & 3.0v, hcmos, smd ds-213 rev a frequency range: description actual size a crystal controlled, hcmos compat- ible oscillator with an internal program- ming feature that allows saronix to sup- ply any frequency in the 1 to 90mhz range. this technology significantly re- duces lead-times from weeks to days. the parts exhibit the same low power, precise rise and fall times, tight symme- try and hcmos drive capability as con- ventional saronix smd oscillators. the parts feature tri-state enable or standby control on pad 1. the packages are min- iature ceramic smd, measuring 5 x 7 x 1.8 mm. 1mhz to 90mhz frequency stability: 25*, 50 or 100 ppm over all conditions: calibration tolerance, operating temperature, input voltage change, load change, 30 day aging, shock and vibration. temperature range: operating: storage: -20 to +70c or -40 to +85c -55 to +125c supply voltage: recommended operating: 3.3v 10% or 3.0v 10% (1 to 40mhz only) supply current: 25ma from 1 to 40mhz, 30ma from 40+ to 90mhz output drive: applications & features quick delivery of any frequency be- tween 1 and 90mhz. suited for use with new hcmos mpus and dsps. tri-state output or standby mode high drive hcmos capability stabilities of 25, 50, 100ppm 5.0v version is available, see sepa- rate data sheet available on tape & reel; 16mm tape, 500pcs per reel symmetry: -20 to +70c: -40 to +85c: 5ns max 20% to 80% v dd 0.4v max v dd -0.4v min 30pf max 1 to 40mhz, 15pf max 40+ to 90mhz @ 3.3v 15pf max 1 to 40mhz @ 3.0v 25ps typ, 50ps max 33+ to 90 mhz 33ps typ, 100ps max 5+ to 33 mhz 117ps typ, 167ps max 1 to 5 mhz rise & fall times: logic 0: logic 1: load: period jitter rms: mechanical: mil-std-883, method 2002, condition b mil-std-883, method 2003 mil-std-883, method 2004, condition d mil-std-883, method 2007, condition a mil-std-202, method 215 mil-std-202, method 210, condition i or j shock: solderability: terminal strength: vibration: solvent resistance: resistance to soldering heat: environmental: thermal shock: moisture resistance: mil-std-883, method 1011, condition a mil-std-883, method 1004 part numbering guide s8002 c s c b ? 90.0000 (t) series saronix programmable oscillator package c = ceramic smd stability tolerance * a = 25ppm, -20 to +70c b = 50ppm, -20 to +70c c= 100ppm, -20 to +70c e = 50ppm, -40 to +85c f = 100ppm, -40 to +85c p = output enable s = standby frequency @ 50% v dd hcmos (3.3v) 1 to 40mhz 45/55% 40/60% @ 50% v dd hcmos (3.3v) 40+ to 90mhz 40/60% 40/60% type c = 3.3v, 1 to 90 mhz d = 3.0v, 1 to 40 mhz @ 50% v dd hcmos (3.0v) 1 to 40mhz 40/60% 40/60% 50a max (use option s, see part number builder) standby current: saronix 141 jefferson drive menlo park ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 tape & reel full reel increments only (500pcs) * please contact saronix for available frequencies @ 25ppm.
all specifications are subject to change without notice. pro tm programmable clock oscillator technical data pro tm s8002 ceramic series saronix 3.3 & 3.0v, hcmos, smd ds-213 rev a tri-state or standby logic table output waveform pin 1 input logic 1 or nc logic 0 or gnd pin 3 output oscillation high impedance/standby required input levels on pin 1: logic 1 = 0.7v dd min logic 0 = 0.2v dd max t f t r cmos symmetry logic 0 20% v dd 50% v dd 80% v dd logic 1 tri-state input test point .01f ( note b ) pin 4 pin 3 v cc out oscillator gnd pin 1 pin 2 ma m v m power supply note: a. c l includes probe and fixture capacitance. note: b. an external .01f bypass capacitor close to package ground and v cc pin is required hcmos (used at saronix) test circuits c l = 30pf, 1 to 40mhz (3.3v) c l = 15pf, 40+ to 90mhz (3.3v) c l = 15pf, 1 to 40mhz (3.0v) ( note a ) solder reflow guide preheat 183 10c 4c/sec max reflow 240 max cooling 4c/sec max 1 ? 2 minutes time 10 sec max 150 200 250 temperature ? c saronix 141 jefferson drive ? menlo park ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 package details 5.08 .200 7.2 .284 pad 1 tri-state control 1.8 .071 max 1.4 .055 1.6 .063 1.2 .047 recommended land pattern * scale: none ( dimensions in ) mm inches 1.8 .071 2.4 .094 12 43 5.08 .200 4.4 .173 s8002c yyww 5.2 .205 pad 2 gnd pad 4 v dd pad 3 output * exact location of items may vary date code 2.0 .079 max max 2.8 .110 denotes pad 1 marking format (exact location of items may vary) * external high frequency power supply decoupling required. control input: disable output delay: 100ns max
|